CS1020 Push and Clinch Grounding Snaps - 10mm Male Stud



$10.32

MRO Essentials

Ground Hardware

100 In Stock


 The CS1020 is an easy to install 10mm grounding snap for ESD matting. The snap can be easily removed, so it can be reused over and over again.

The CS1020 push & clinch snaps are the ideal snap for use with ESD matting such as multi-layer rubber or vinyl mats. The pronged 3/8" (10mm) stud is an easy way to install snaps used to connect ESD ground cables to mats such as the CP2524 common point ground cable.  The snap provides a strong contact for table matting. The bendable pronged teeth allow the snap to be removed and used over again.


  • ESD PROTECTION: The CS1020 is an easy to install 10mm grounding snap for ESD matting.

  • INSTALLATION: The "Push and Clinch" prongs are pushed ESD materials and the prongs are bent to hold in place

  • REUSABLE: The snap can be easily uninstalled by bending prongs, so it can be reused over and over again.

  • SIZE: 10mm (3/8in) snap size fits standard ESD equipment.

  • SNAP: The CS1020 is a Male Stud.  Also available - CS1010 Female Socket.

  • Sold in Packs of 10 snaps
  •  

    Grounding snaps are used to connect a ground cord to a work surface static safe mat or a ESD floor mat. An antistatic floor mat or ground mat is one of a number of antistatic devices designed to help eliminate static electricity. It does this by having a conductive material embedded within the mat that collects the static.

    How to Install Clinch Snaps
    1. Locate the safest and most convenient snap location.
    2. Press the snap down on the top side until prongs puncture matting and are fully visible on the underside of the mat.
    3. Bend the prongs of the snaps until flush against the underside of the mat.
    4. Bend the prongs up to remove the snap from the matting.

     

    CARRIERS:
    MRO Essentials ships via the following companies:

  • UPS
  • FedEx
  • USPS
  • DHL (International Only)
  • LTL Freight: Various Carriers

  • SHIPPING TIMES:
    Orders placed before 12 noon Eastern typically ship the same day.

    SHIPPING CHARGES:
    All shipments are FOB FACTORY. Purchaser is therefore responsible for both shipping charges and damage to goods in transit. Note that freight charges are based on weight AND volume. Assembled items take up a greater shipping volume and are typically charged at a higher freight rate than items shipped flat. Purchaser must specify a freight carrier at time the order is placed or MRO Essentials will choose a carrier and prepay shipments. The freight cost of prepay shipments will be added to each invoice unless otherwise specified. NOTE: Request to ship UPS 1st, 2nd, or 3rd day is a method of shipment and does not imply any expediting of order processing by MRO Essentials. For non-UPS shipments, the order will be shipped freight collect or third party billing at purchaser’s option. Purchaser is responsible for and agrees to pay (1) charges disallowed or billed back to MRO Essentials by third parties when purchaser has specified third party billing and (2) charges billed to MRO Essentials for corrections made by the carrier including address corrections. Some carriers may not be available to be used by MRO Essentials. Purchaser will be notified if an alternate carrier is required.

    MULTIPLE SHIPPING POINTS:
    MRO Essentials products are manufactured in various locations. Shipping points may vary and may change without prior notice.

    INSURING YOUR SHIPMENT:
    You are responsible for your shipment once it leaves the F.O.B. point. We recommend that you insure all shipments. It is our policy to insure shipments unless otherwise specified. The buyer is responsible for uninsured lost or damaged shipments.

    Related Products